← Blog Material Selection Robotics →

Robot Material Selection, One Page: Part × Environment × Material × Finish

Stop asking which material is best. Five diagrams settle material, environment, finish and cost for every robot part — built for makers working on a budget.

Procurement Department · ·7 min read

The first thing that stalls a robot build is not the CAD. It is picking material. 6061, 7075, stainless, titanium, carbon fiber — spread out a spec table and you end up more confused than when you started.

The problem is the question. “Which material is best” has no answer. There is no best material, only the right one for the job.

This is not a materials encyclopedia. It is a way to match things up: answer four questions, then check five diagrams. When you finish, you can say “this part gets this material, not that one.” That is enough.

For the deep dive on joints, jump to the two longer articles at the end.

1. Answer four questions before you pick anything

Not picking material — answering four questions 1 What environment? Humidity, heat, cleanliness rule some out 2 How much load? Static, repeated starts, or impact 3 Is weight critical? Every gram at the tip costs the whole arm 4 Where does the money go? Upgrade only what really carries load
Figure 1 · Order matters: environment eliminates options, load sets strength, weight sets specific strength, budget decides what to upgrade

The first question gets skipped most often. Environment is not a footnote. It can rule out half your options before you draw anything. A prototype that runs fine on a bench can fail in three months in a humid shop.

The second is the most misunderstood. Robots see repeated start-stop cycles, not static load. Fatigue strength is typically only 30–40% of tensile strength. Size against static strength and the part runs borderline.

2. Six parts, match them up

Six parts, six materials, matched Frame / base 6061-T6 best value Joint / flange 7075-T6 / 17-4PH local only Drive interface 4140 / 4340 steel ground Gripper / tip 6061 / POM light wins Shell / guard 5052 sheet bend, don't mill Bushings POM / UHMW-PE self-lubricating
Figure 2 · Default the whole robot to 6061 and plastic; only the joint and drive rows are worth upgrading

One line to remember: spend on the parts that carry load. Everything else is 6061, plastic, and bought-in parts.

For long members, buy extrusion and machine the ends instead of hogging from solid bar — far less scrap. For housings, bent 5052 sheet costs 10–20% of a solid milled block. Bearings, guides, and reducers: buy catalog parts. Never machine what you can order.

The subsystem-by-subsystem cost breakdown is in Robot Parts Materials.

3. Change the environment, change the answer

Same robot, different environment, different answer Indoor 6061 + standard anodize Cheapest, and quite enough Humid / salt 316L, or sealed hard anodize Bare 7075 stress-corrodes Cleanroom 316L electropolished Leave outgassing plastics behind High heat Steel, or titanium Aluminum softens past 150 °C
Figure 3 · Environment first: humidity means corrosion, cleanrooms mean outgassing, heat means softening — not hardness

Two common mistakes are worth correcting.

Stainless for humidity is about corrosion, not hardness. Chromium forms a passive film that stops corrosion. Hardness is not the selling point. If you want hardness, martensitic steels are harder; if you want light weight, stainless is heavier. The real cost is work hardening, poor thermal conductivity, and gummy chips.

Titanium is not just expensive. Its thermal conductivity is about 7 W/(m·K), one twenty-fourth of aluminum. A joint housing also has to shed heat; titanium traps it inside. And here is the counterintuitive part: the specific stiffness of aluminum, magnesium, titanium, and steel is nearly identical — a narrow band of 24 to 26. Swapping aluminum for titanium to save weight delivers far less than expected. Material solves strength; structure solves stiffness.

Carbon fiber is the same story. Its specific stiffness and strength are genuinely high, but it is anisotropic, weak in interlaminar shear, and prone to edge delamination. It suits long arm links, not joint housings that need drilled and tapped holes. Don’t use it because it sounds premium.

4. Pair the finish with the material

The finish is part of the material choice 6061 Anodize — mask where you need conductivity 7075 Hard anodize — allow for bearing fit Steel Nickel / black oxide — bare steel rusts 316L Passivate — electropolish for clean use Titanium Anodize for color — not for heat sinking
Figure 4 · Decide the finish when you choose the material, not after the parts are made

Coating thickness is the easy trap. It can be measured, so it sits on the verifiable side — but those few microns of anodic growth eat into fit dimensions. Mask bearing seats or compensate for film thickness on the drawing. That decision happens before release, not after plating. The full calculation is in Anodizing and Dimension Control.

5. Which layer deserves the money

Spend at the edge, not across the whole robot Default 6061 / POM / catalog parts Form saves 5052 sheet / 4140 steel Local upgrade 7075 / 17-4PH / 316L Special cases Ti / PEEK
Figure 5 · Cost climbs to the right. Most parts stay on the default row; upgrades happen in one or two places

Three savings moves have nothing to do with grade:

Change the form. Sheet metal for thin panels, extrusion for long members, die casting or injection molding for volume, CNC for prototypes. This often saves more than changing alloy.

Dare to use plastic. Grippers, bushings, guards — plastic is not just cheaper, often better. Lighter, quieter, no lubrication.

Do DFM early. Wall thickness, the tolerance you truly need, feature simplification. Those three cut machining cost before the first cut.

6. Makers on a budget: what to spend on first

Engineers and makers fail differently. Engineers fear design failure; makers fear running out of money before the thing moves.

Spend in this order:

  1. Build version one from the default layer in Figure 2. Don’t touch titanium or carbon fiber yet.
  2. Upgrade only the part that broke — change that one to 7075 or steel. Don’t upgrade the whole arm.
  3. Buy every catalog part you can. Don’t machine bearing blocks and reducers.
  4. Fix the finish on the drawing. Don’t discover a plated bearing seat after the fact.
  5. When unsure, ask “is there a cheaper material that does this job?” Usually there is.

What we can take off your plate: before quoting, we flag which operations land on the “cannot verify afterward” side; we stock aluminum, steel, titanium, and engineering plastics, from one-off prototypes to small batches, with no minimum order; quotes go out in 2 hours, prototypes in 3–7 days; EN 10204 3.1 certificates and heat-lot traceability are available.

Send a drawing, get a quote in 2 hours

Frequently asked questions

Should every robot be 6061? Most structural parts, yes. Joints, drives, and wear parts often need an upgrade. The default layer is a starting point, not the finish line.

Does a humid environment mean all stainless? No. A whole 316L robot costs more and weighs more. Use stainless for the local parts that see moisture; hard-anodize and seal the rest.

Is carbon fiber better than aluminum? Not “better” — different, anisotropic. Great for long links; not necessarily better for a joint housing that needs holes and heat paths.

Budget for one upgrade only. Which part? The part that fails first. Usually a joint flange or a loaded end-effector piece, never the housing.

Go deeper

Parameter ranges come from the two articles above, both already published on this site. Selection criteria agree with common-grade data for 6061-T6, 7075-T6, and Ti-6Al-4V; always confirm the current mill certificate for the specific grade.

Got a question about anything in this article?

Ask an engineer →
Share LinkedIn Email

Have a Part to Machine? Let's Talk.

Send us your STEP or PDF and get a free DFM review and quote within 2 hours.